NOTE: It is reported that most of the new interfaces now have this problem! I did it in a hurry just for the so don't blame for the soldering quality on the pictures. I did it directly on the OBD connector as it was easier for me. Remove the single terminating 120 Ohm (or whatever) resistor from the interfaceģ. Get two resistors of 100 Ohm and 2 capacitors of 560 pF. So i just got two 100 Ohm resistors and two capacitors of 560 pF and fixed my interface as shows below. The problem is actually in the CAN termination method used in these interfaces - they use one 120 Ohm resistor connected between CAN-L and CAN-H.Īccording to the ELM327 datasheet the proper termination is to use 100 Ohm resistor on each of the 2 lines connected to ground through a 560 pF capacitor (see the picture below). Well, it seems that the problem is electrical and is not very hard to fix. I also have one of these "faulty" units and decided to play with it and see what is wrong. There was one user here who bought 5 of these cheap interfaces with no luck and finally bought an expensive one. A lot of people are having problems with some chinese ELM interfaces that cannot connect to CAN network even if they support all ELM 1.3 commands properly.
0 Comments
You will not make or have made, or permit to have made any copies of the Software or portions thereof, except as necessary provided, however, that you may make one copy for back-up purposes for its use with the authorized number of systems hereunder. You agree to maintain the Software and other proprietary information in strict confidence and to establish reasonable procedures regulating access to and use of the Software. No rights are granted to you other than a License to use the Software on the terms expressly set forth in this Agreement. Fonts can be embedded in files such as Adobe Acrobat PDF files for viewing and printing purposes only. You acknowledge that licensing fees for the Macintosh and PC formats are separate and individual fees. If you need to have access to the Software on more than five 5 CPUs, you must pay Phil's the applicable fees for typefaces used in a multi-system environment. Under the terms of this License Agreement, you have the right to use the software on up to five 5 CPUs. To stop User-Initiated Safe mode, exit the program then start it again normally. At the command prompt, use the /safe option when you start the program.In all cases you will need to start Outlook 2010 in safe mode. Apart from add-ins, there could be hundreds of other reasons why your Outlook is crashing. Press and hold the CTRL key, and then click the name of the Microsoft Office program that you want to run. If your Outlook 2010 is crashing due to a culprit add-in, then the only possible way is to start it in safe mode and remove the add-in.Click Start, point to All Programs, and then point to Microsoft Office.To start a Microsoft Office program in User-Initiated Safe mode: Note: Since Raystafarian’s answer was a bit brief, we have added a small bit from the link he shared below. You can find more info on Microsoft Office’s Safe Mode here. If you are having problems with a Microsoft Office program, you may be able to use User-Initiated Safe mode to make it possible to run the program. Start Outlook in safe mode: outlook.exe /safe SuperUser contributor Raystafarian has the answer for us: Is there a simple, straightforward way to deal with a problematic Outlook add-in? The Answer My problem is that Outlook 2013 will not start at all because it gets stuck at start-up while it tries to load the TeamViewer add-in. SuperUser reader f.ardelian needs to know how to disable a problematic add-in without starting Outlook:Īll the guides I have found online start with “go to the Tools menu”. and you can't resell them easily (or at all?), while used UI equipment gets sold on eBay like new. It still might make sense to sell those and buy Unifi - you can use unifi cameras with Surveilance Station (SS), but SS licenses are paperweight without surveillance station. And I do keep trying it every year just for fun to see if anything changed. And yet, surveillance station fails at doing them effectively. I don't think those are unreasonable scenarios: Open app to see what's going on now, and scrub back to see what happened in the past. And scrubbing from a mobile app is unusable on Surveilance station while with protect - is magically awesome (they pre-load a bunch of thumbnails) I meant how long does it takes to see the stream from the time you start the application. I don’t see any latency on the cameras either in the The price point of the cameras is too high for the basic use I have internally.Įven Flex? I almost exclusively use Flex-es everywhere. The conversation flew so smoothly I did not not notice. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |